`1998 State Competition - 50 points`	`Name`
`FFA Agricultural Mechanics Contest`	`Contestant Number`
`University of Missouri`	`Chapter`

REPAIR AND MAINTENANCE

Contest Components:

Tool ID

Identify 10 selected tools
2 points per tool for a total of 20 points

Blade Sharpening

Give students a 8" x 1.5" x 3/16" piece of metal with a pre-drilled hole in the center.
Sharpen two edges and balance as if it where a lawn mower blade.

Grading Scorecard

Item	Points Possible	Points Earned
Blade is balanced	5	.
Angle on blade is correct	5	.
Edge is even	5	.
Cutting edge is 2" long	5	.
Loss of temper	5	.
Safety	5	.
Total Points	30	.

Tool Identification

Directions: Select the most correct answer and record your answer on the scantron sheet provided.

1. The tool tagged #1 is a/an:

a. auger bit.

b. masonry bit.

c. router bit.

d. spade bit.

2. Indicate the condition of the tool tagged #1.

a. Yes, the tool is properly sharpened, fitted, or adjusted.

b. No, the tool is not properly sharpened, fitted or adjusted.

3. The tool tagged #3 is a:

a. clutch head screwdriver.

b. torque screwdriver.

c. standard screwdriver.

d. phillips screwdriver.

4. Indicate the condition of the tool tagged #3.

a. Yes, the tool is properly sharpened, fitted, or adjusted.

b. No, the tool is not properly sharpened, fitted or adjusted.

5. The tool tagged #5 is a/an:

a. combo pliers.

b. diagonal cutting pliers.

c. lineman's pliers.

d. groove joint pliers.

6. Indicate the condition of the tool tagged #5.

a. Yes, the tool is properly sharpened, fitted, or adjusted.

b. No, the tool is not properly sharpened, fitted, or adjusted.

7. The tool tagged #7 is a/an:

a. inside caliper.

b. outside caliper.

c. vernier caliper.

d. sheet metal gauge.

8. Indicate the condition of the tool tagged #7.

a. Yes, the tool is properly sharpened, fitted, or adjusted.

b. No, the tool is not properly sharpened, fitted or adjusted.

9. The tool tagged #9 is a:

a. cold chisel.

b. air chisel.

c. wood chisel.

d. diamond point chisel.

10. Indicate the condition of the tool tagged #9.

a. Yes, the tool is properly sharpened, fitted, or adjusted.

b. No, the tool is not properly sharpened, fitted or adjusted.

11. The tool tagged #11 is a:

a. line level.

b. mason's level.

c. mechanics level

d. aluminum level.

12. Indicate the condition of the tool tagged #11.

a. Yes, the tool is properly sharpened, fitted, or adjusted.

b. No, the tool is not properly sharpened, fitted or adjusted.

13. The tool tagged #13 is a/an:

a. carpenters square.

b. combination square.

c. steel square.

d. try square.

14. Indicate the condition of the tool tagged #13.

a. Yes, the tool is properly sharpened, fitted, or adjusted.

b. No, the tool is not properly sharpened, fitted or adjusted.

15. The tool tagged #15 is a:

a. flat bastard file.

b. flat mill file.

c. file card.

d. wood rasp.

16. Indicate the condition of the tool tagged #15.

a. Yes, the tool is properly sharpened, fitted, or adjusted.

b. No, the tool is not properly sharpened, fitted or adjusted.

17. The tool tagged #17 is a:

a. compass saw.

b. coping saw.

c. crosscut saw.

d. miter saw.

e. hack saw.

18. Indicate the condition of the tool tagged #17 a:

a. Yes, the tool is properly sharpened, fitted, or adjusted.

b. No, the tool is not properly sharpened, fitted or adjusted.

19. The tool tagged #19 is a:

a. adjustable NC die.

b. pipe die.

c. non-adjustable NC die.

d. metric die.

20. Indicate the condition of the tool tagged #19.

a. Yes, the tool is properly sharpened, fitted, or adjusted.

b. No, the tool is not properly sharpened, fitted or adjusted.