You will have approximately 20 minutes to identify 10 tools and repair the threads on the quarter inch bolt provided.

REPAIRING THE THREADS ON THE QUARTER INCH BOLT

Bench grinder, 1/4" bolt, nut, die, die stock, hacksaw, cutting oil, pliers
 

Directions:

1. Place the 1/4" bolt in the vice.
2. Remove the damaged portion of the bolt, approximately 1/4".
3. Insert the die into the diestock and secure.
4. Use the die stock and die to recondition the damaged threads.
5. Turn in the following for grading to one of the judges

a - this evaluation score sheet
b - your 1/4" bolt
c - the end you removed from the bolt

Note: the part which is beyond the dashed line below should be removed with a hacksaw.
 
 

                                                                                                        Points

                                                                                                Possible   Earned
 

1. Nut starts easily...............................................................         5         _____

2. Nut travels down the entire length of the bolt easily..........          5         _____

3. Threads on the bolt are positioned perfectly........................       5         _____

4. A reasonable amount of bolt was removed..........................      5          _____

5. Overall appearance.............................................................     5          _____

6. Safety/work habits.............................................................      5          _____

7. Total from Tool Identification............................................     20          _____
 

Total Points...                                                                          50          _____
 

Instructions: Select the most correct answer and record your answer on the scantron sheet provided.
 

1. The tool tagged # 1 is a:

a. Masonry Bit
b. Router Bit
c. Spade Bit
d. Auger Bit

2. Is the tool tagged # 1 in good working condition?

a. Yes, the tool is properly fitted or adjusted.
b. No, the tool is NOT properly fitted or adjusted.
 

3. The tool tagged # 3 is a:

a. Ripping Hammer
b. Sheet Metal Setting Hammer
c. Rawhide Hammer
d. Mallet

4. Is the tool tagged # 3 in good working condition?

a. Yes, the tool is properly fitted or adjusted.
b. No, the tool is NOT properly fitted or adjusted.

5. The tool tagged # 5 is a:

a. Tinner Snips
b. Aviation Snips
c. Wire cutters
d. Scissors

6. Is the tool tagged # 5 in good working condition?

a. Yes, the tool is properly fitted or adjusted.
b. No, the tool is NOT properly fitted or adjusted.

7. The tool tagged # 7 is a:

a. Nut wrench
b. Nut driver
c .Starter wrench
d. Clutch Head Screwdriver

8. Is the tool tagged # 7 in good working condition?

a. Yes, the tool is properly fitted or adjusted.
b. No, the tool is NOT properly fitted or adjusted.

9. The tool tagged # 9 is a:

a. Nail set
b. Nail punch
c. Scratch Awl
d. Scribe

10. Is the tool tagged # 9 in good working condition?

a. Yes, the tool is properly fitted or adjusted.
b. No, the tool is NOT properly fitted or adjusted.

11. The tool tagged # 11 is a:

a. Back Saw
b. Coping saw
c. Compass Saw
d. Shear Saw

12. Is the tool tagged # 11 in good working condition?

a. Yes, the tool is properly fitted or adjusted.
b. No, the tool is NOT properly fitted or adjusted.

13. The tool tagged # 13 is a:

a. Tap Wrench
b. Tap Handle
c. Die Stock
d. Bar Clamp

14. Is the too tagged # 13 l in good working condition?

a. Yes, the tool is properly fitted or adjusted.
b. No, the tool is NOT properly fitted or adjusted.

15. The tool tagged # 15 is a:

a. Wet Stone
b. Wetting Stone
c. Oil Stone
d. Sharpening Stone

16. Is the tool tagged # 15 in good working condition?

a. Yes, the tool is properly fitted or adjusted.
b. No, the tool is NOT properly fitted or adjusted.

17. The tool tagged # 17 is a:

a. Universal Joint
b. Flex Socket
c. Adapter
d. 12 point socket

18. Is the tool tagged # 17 in good working condition?

a. Yes, the tool is properly fitted or adjusted.
b. No, the tool is NOT properly fitted or adjusted.

19. The tool tagged # 19 is a:

a. Pipe Slicer
b. Pipe Die
c. Pipe Tap
d. Pipe Cutter

20. Is the tool tagged # 19 in good working condition?

a. Yes, the tool is properly fitted or adjusted.
b. No, the tool is NOT properly fitted or adjusted.